General Description
Basic unit includes rear mounted welded base assembly supporting rotating rear mounted turret, hydraulically powered rotation gear box, oil reservoir, oil, manual hydraulic controls mounted in 30” lockable box at rear of unit. Electronic proportional three stick remote controls on platform. Torsion bar provides stabilization. Rectangular steel two section hydraulically telescoping boom with one 5” double acting lift cylinder. Hydraulically self-leveling 24" x 48" work platform with remote leveling from platform, power take-off, pump, holding valves on all cylinders, fire extinguisher, remote start/shutdown at upper and lower controls, pressure gauge and a body harness. Paint Hi-reach white, outriggers red and bed and boxes black. Installed on chassis, tested and ready to operate. Working Height 41 ft. Platform Capacity 300 lbs.

Specifications

Minimum Platform Height
36' ground to platform floor.

Working Range
41' max. height and 33' max. side reach with boom horizontal.

Work Platform
24"x48" platform with 40" rails. Equipped with one safety harness lanyard attachment loop. One safety harness with 72" lanyard provided. Standard rating 300 lbs.

Platform Leveling System
Hydraulic "closed" system consisting of a platform cylinder interacting with a boom-actuated master cylinder mounted in boom support turret. System is provided with factory-set relief valves to compensate for oil expansion or overload during platform leveling operation. Releveling controls provided in platform and at ground controls to give purging and releveling capability.

Platform Controls
Three individual proportional electronic controllers with adjustable ramping meter pilot-operated, pressure-compensated modulating valves for smooth platform operation. The boom ground controls are mounted at rear of truck. Remote controls for boom operations from platform operate from a removable remote control box. Current is supplied to the electric remote controls through a cord in center of turret to an internal cable carrier inside of the boom.

Lower Control Box
Steel box with lockable door at rear of unit.

Frame
One piece, all welded, box-type fabrication. Bolt-on torque frame distributes load through truck frame.

Turret
Reverse offset turret is one-piece weldment. Turret rotates on large diameter ball bearing.

Rotation
360 degree non-continuous. Hydraulic motor drives turret through gear box.

Boom
Fixed boom section made of steel rectangular tube with 1/4" wall thickness. Extension boom section made of steel rectangular tube with 3/16" wall thickness. Assembly includes heavy-duty cylinder fittings, pivot pins, and replaceable wear pads.

Boom Extension
One 2 1/2" internal cylinder extending the outer boom section.

Lift
Double-acting 5" full displacement, long-stroke cylinder provides smooth and stable boom elevation. Holding valve prevents boom from falling in event of hose failure.

Cylinders
All cylinders use micro-honed cylinder tubing, chrome shafts, top grade packing and protective rod wipers. Cylinder-mounted holding valves provided on all load holding cylinders.

Hoses
All high pressure hose is wire braid reinforced with a minimum safety factor of 4 to 1.

Oil Tank Capacity
35 Gallon remote mounted.

Hydraulic System
Operating pressure approximately 1,500 PSI. System is parallel open-center type and is equipped with liquid-filled pressure gauge. Oil is supplied to upper cylinders through hoses in center of turret to an internal cable carrier inside of the boom.

Pump
Gear type, direct mount to truck PTO. 12 GPM @ 1,800 PSI on high engine speed.

PTO
Heavy-duty, high-speed. Cable engaged from cab.

Cab Equipment
PTO cable with indicator lights installed in truck cab. Engine speed control and start/kill installed with control switches in platform remote control box and lower control box. U/L approved 5
BC dry chemical fire extinguisher installed in truck cab.

Operators Manual & Video
Two copies of operation, maintenance, safety and parts manual provided with each unit. Operational and safety video provided at delivery.

Installation
Unit installed on customer's truck, painted, system and tank filled with oil, tested, inspected, certified and ready to operate.

Standard Paint
Top of bed painted with black nonskid surface. Underside of bed painted black. Rub rail, ground control box, oil reservoir, turret base, turret, boom and platform painted red, white or black.

Bumper
Bureau of Motor Carrier Safety rear bumper.

Weight
Approximately 7,000 lbs. with 12' steel floor bed less truck.

Truck Chassis
Approximately 84" C.A., 5,000 lb. front axle and 11,000 lb. rear wide-track axle, and 15,000 lb. GVWR required. Recommended GVWR is minimum for HI-REACH with flatbed only. Contact factory when additional equipment is to be added.

Options

Color
You may order your fleet colors.

Line Body
Aluminum or steel with 13'-4" length, a 92" width, a tread plate floor, and eight compartments.

Hydraulic Platform Rotation Outriggers
Elliott "V" type at rear with telescoping vertical section for stable 92 inch spread.

Winch
1,000 lb. hydraulic winch with 90 ft. of 3/16" cable installed on boom with control valve in lower control box.

Bed
Length 12' (other lengths available). Width 94" with 1/8" steel tread plate floor or wood floor, 6" rub rail and heavy cross members. Stake pockets on both sides. Two-step grip strut rear ladder with two grab handles located on both sides. Chassis stop/turn/back-up lights remounted as necessary. Rear clearance and side marker lights and reflectors installed on bed.

• Belt Drive PTO with electric clutch (for units with automatic transmission).
• 110V Line to Platform
• Cab Guard

THIS AERIAL DEVICE IS NON-INSULATING. IT PROVIDES NO ELECTRICAL PROTECTION. CONTACT WITH OR INADEQUATE CLEARANCE TO AN ENERGIZED LINE OR APPARATUS IS AN ELECTROCUTION HAZARD.

Elliott Equipment Company reserves the right to change the specification of any unit at any time without prior notice. This document is only a statement of general specifications on the date of this publication.